Ústav fyziky materiálů AV ČR, v. v. i. > Zaměstnanci > Kunčická Lenka

Ing. Lenka Kunčická, Ph.D.

Místnost219
Telefon+420 532 290 371
E-mail[javascript protected email address]
Researcher IDC-6217-2019
Pozicevědecký pracovník - Skupina perspektivních vysokoteplotních materiálů


2022




2021

Kunčická L., Jopek M., Kocich R., Dvořák K.: Determining Johnson-Cook Constitutive Equation for Low-Carbon Steel via Taylor Anvil Test. Materials 14 (2021) 4821

Kunčická L., Jambor M., Weiser A., Dvořák J.: Structural Factors Inducing Cracking of Brass Fittings. Materials 14 (2021) 3255

Kunčická L., Halama R., Fusek M.: Special Issue: Selected Papers from Experimental Stress Analysis 2020. Materials 14 (2021) 1136

Král P., Dvořák J., Král L., Sklenička V., Horita Z., Takizawa Y., Tang Y., Kunčická L., Kvapilová M., Svobodová M.: Paper 035: Creep behaviour and microstructure changes of heat resistant steel P92 processed by severe plastic deformation. ECCC 2021, 5th Int. Creep and Fract. Conf. 2021 (2021) 123-132

Král P., Dvořák J., Sklenička V., Horita Z., Takizawa Y., Tang Y., Kunčická L., Kvapilová M., Ohankova M.: Influence of High Pressure Sliding and Rotary Swaging on Creep Behavior of P92 Steel at 500 °C. Metals 11 (2021) 2044

Kořínek M., Halama R., Fojtík F., Pagáč M., Krček J., Krzikalla D., Kocich R., Kunčická L.: Monotonic Tension-Torsion Experiments and FE Modeling on Notched Specimens Produced by SLM Technology from SS316L. Materials 14 (2021) 33

Král P., Dvořák J., Sklenička V., Masuda T., Tang Y., Horita Z., Kunčická L., Kuchařová K., Kvapilová M., Svobodová M.: Effect of severe plastic deformation on creep behaviour and microstructure changes of P92 at 923 K. Kovové materiály 59 (2021) 141 -148

Kunčická L., Kocich R.: Effects of Temperature (In)homogeneity during Hot Stamping on Deformation Behavior, Structure, and Properties of Brass Valves. Adv. Eng. Mater. 12 (2021) 2101414

Chlupová A., Šulák I., Kunčická L., Kocich R., Svoboda J.: Microstructural aspects of new grade ODS alloy consolidated by rotary swaging. Mater. Character. 181 (2021) 111477

Král P., Dvořák J., Kunčická L., Kocich R., Kvapilová M., Svobodová M., Sklenička V.: Influence of Rotary Swaging on Creep Behaviour of P92 Steel. IOP Conf. Ser.: Mater. Sci. Eng. 1190 (2021) 012033

Král P., Dvořák J., Sklenička V., Horita Z., Takizawa Y., Tang Y., Kunčická L., Kuchařová K., Kvapilová M., Svobodová M.: INFLUENCE OF SEVERE PLASTIC DEFORMATION AND SUBSEQUENT ANNEALING ON CREEP BEHAVIOUR OF MARTENSITIC 9% CR STEEL . METAL 2021 Conf. Proc. 2021 (2021) 429-434



2020

Král P., Blum W., Dvořák J., Yurchenko N., Stepanov N., Zherebtsov S., Kunčická L., Kvapilová M., Sklenička V.: Creep behavior of an AlTiVNbZr0.25 high entropy alloy at 1073 K. Mater. Sci. Eng. A 783 (2020) 139291

Kocich R., Kunčická L.: Special Issue: Mechanical Properties in Progressive Mechanically Processed Metallic Materials. Materials 13 (2020) 4668

Svoboda J., Kunčická L., Luptáková N., Weiser A., Dymáček P.: Fundamental Improvement of Creep Resistance of New-Generation Nano-Oxide Strengthened Alloys via Hot Rotary Swaging Consolidation. Materials 13 (2020) 5217

Kunčická L., Kocich R., Klečková Z.: Effects of Sintering Conditions on Structures and Properties of Sintered Tungsten Heavy Alloy. Materials 13 (2020) 2338

Kunčická L., Kocich R.: Effect of Swaging Temperature on Deformation Behaviour of W93Ni6Co1 tungsten Heavy Alloy. Key Eng. Mater. 865 (2020) 91-96

Král P., Dvořák J., Blum W., Sklenička V., Horita Z., Takizawa Y., Tang Y., Kunčická L., Kocich R., Kvapilová M., Svobodová M.: The Effect of Predeformation on Creep Strength of 9% Cr Steel. Materials 13 (2020) 5330

Kunčická L., Klečková Z.: Structure Characteristics Affected by Material Plastic Flow in Twist Channel Angular Pressed Al/Cu Clad Composites. Materials 13(18) (2020) 4161

Kunčická L., Macháčková A., Lavery N., Kocich R., Cullen J., Hlaváč L.: Effect of thermomechanical processing via rotary swaging on properties and residual stress within tungsten heavy alloy. International Journal of Refractory Metals and Hard Materials 87 (2020) 105120

Svoboda J., Kunčická L., Luptáková N., Weiser A., Dymáček P.: Fundamental Improvement of Creep Resistance of New-Generation Nano-Oxide Strengthened Alloys via Hot Rotary Swaging Consolidation. Materials 13 (2020) 5217

Kunčická L., Kocich R.: Correlating Structure and Electrical Properties in Rotary Swaged Al/Cu Clad Composites. Key Eng. Mater. 865 (2020) 85-90

Kunčická L., Kocich R.: Sub-Structure and Residual Stress in Rotary Swaged Cu/Al Clad Composite Wires. Key Eng. Mater. 865 (2020) 7-12

Kunčická L., Macháčková A., Petrmichl R., Klečková Z., Marek M.: Optimizing Induction Heating of WNiCo Billets Processed via Intensive Plastic Deformation. Applied Sciences 10 (2020) 8125



2019

Kunčická L., Král P., Dvořák J., Kocich R.: WE43 BIOCOMPATIBLE ALLOY AFTER SEVERE PLASTIC DEFORMATION: STRUCTURE CHARACTERIZATION. METAL 2019 Conf. Proc. 1 (2019) 1284-1290

Kunčická L., Kocich R., Ryukhtin V., Cullen J., Lavery N.: Study of structure of naturally aged aluminium after twist channel angular pressing. Mater. Character. 152 (2019) 94-100

Málek J., Zýka J., Lukáč F., Čížek J., Kunčická L., Kocich R.: Microstructure and Mechanical Properties of Sintered and Heat-Treated HfNbTaTiZr High Entropy Alloy. Metals 9(12) (2019) 1324

Kunčická L., Macháčková A., Krátká L., Kocich R.: Analysis of Deformation Behaviour and Residual Stress in Rotary Swaged Cu/Al Clad Composite Wires. Materials 12 (2019) 3462

Kunčická L., Kocich R., Dvořák K., Macháčková A.: Rotary swaged laminated Cu-Al composites: Effect of structure on residual stress and mechanical and electric properties. Mater. Sci. Eng. A 742 (2019) 743-750

Kunčická L., Král P., Dvořák J., Kocich R.: Texture Evolution in Biocompatible Mg-Y-Re Alloy After Friction Stir Processing. Metals 9(11) (2019) 1181

Král P., Staněk J., Kunčická L., Seitl F., Petrich L., Schmidt V., Beneš V., Sklenička V.: Microstructure changes in HPT-processed copper occurring at room temperature. Mater. Character. 151 (2019) 602-611



2018

Kocich R., Kunčická L., Král P., Strunz P.: Characterization of innovative rotary swaged Cu-Al clad composite wire conductors. Mater. & Design 160 (2018) 828-835



2016

Kočích R., Kunčická L., Král P., Lowe T.: Texture, deformation twinning and hardening in a newly developed Mg-Dy-Al-Zn-Zr alloy processed with high pressure torsion. Mater. & Design 90 (2016) 1092-1099

Kočích R., Kunčická L., Král L., Macháčková A.: Sub-structure and mechanical properties of twist channel angular pressed aluminium. Mater. Character. 119 (2016) 75-83

Kunčická L., Kočích R., Král P., Pohludka M., Marek M.: Effect of strain path on severely deformed aluminium. Mater. Lett. 180 (2016) 280-283