---

Guth S., Babinský T., Antusch S., Klein A., Kuntz D., Šulák I.: Comparison of electron-beam-melted and conventionally rolled Inconel 718 under thermomechanical creep-fatigue loading. Int. J. Fatigue 202 (2026) 109238

---

Bae J., Tekoglu E., Alrizqi M., O Brien A., Liu J., Biggs K., Kim S., Penn A., Šulák I., Chen W., So K., Hart J., Sim G., Li J.: Additive manufacturing of strong and ductile In939+TiB2 by laser powder bed fusion. Mater. Sci. Eng. A 939 (2025) 148446

Hloch S., Souček K., Svobodová J., Chlupová A., Nag A.: On the subsurface erosion, micro-tunneling and deformation induced by high-frequency droplet impingement in gravity-cast aluminum, analyzed through micro-computed tomography. Results in Engineering 27 (2025) 105669

Bartošák M., Mára V., Vražina T., Španiel M., Šulák I.: Low-cycle fatigue behaviour of boron-added 9% Cr martensitic steel: Effects of temperature, strain rate, and strain amplitude. Int. J. Fatigue 200 (2025) 109110

Chlupová A., Poloprudský J., Nag A., Klichová D., Stolárik G., Foldyna J., Petrů J., Pagáč M., Hajnyš J., Man J., Fintová S., Jambor M., Hloch S.: Water droplet erosion response of 316L steel manufactured conventionally and additively using selective laser melting. Results in Engineering 28 (2025) 108069

Chlupová A., Poloprudský J., Nag A., Klichová D., Souček K., Pude F., Hloch S.: Micro-computed tomography (micro-CT) quantification of erosion wear and delamination of carbon fiber reinforced polymers (CFRP). Wear 570 (2025) 205957

Slone C., Kaplowitz D., Bowers M., Roepke C., Mazánová V., James B., Aguiar D.: Effects of heat treatment on vintage pipeline electric resistance welds. Metall. Mater. Trans. A 56 (2025) 3670-3680

Polák J., Poczklán L., Vražina T.: Dislocation structure near the intergranular fracture surface of cyclically strained polycrystalline copper. Fatigue Fract. Eng. Mater. Struct. 48 (2025) 3110-3121

Chlupová A., Poloprudský J., Nag A., Stolárik G.: Hydrodynamic erosion of copper with different grain sizes. MM Science Journal 2025 (2025) 8654-8663


Poloprudský J., Sobola D., Daniel J., Grossman J., Kruml T.: Effect of repeated solid impact on bulk metallic materials. Surfaces and Interfaces 62 (2025) 106159

Bartošák M., Mára V., Slaný M., Šulák I.: Effect of phase angle on thermo-mechanical fatigue behaviour of boron-added 9% Cr martensitic steel. Eng. Fract. Mech. 330 (2025) 111650

Ravasio C., Conconi S., Stehle D., Pude F., Poloprudský J., Šiška F., Chlupová A., Hloch S.: Erosion in the contact periphery in the initiation zone due to erosion of abrasive water jet. The International Journal of Advanced Manufacturing Technology 136 (2025) 3641-3653

Utada S., Heczko M., Rame J., Hamadi S., Dlouhý A., Kruml T., Villechaise P., Reed R., Mills M., Cormier J.: Origin of localizing creep damage in Ni-based single crystal superalloys pre-strained at room temperature. Acta Mater. 299 (2025) 121448

Fawaeer S., Al-Qaisi W., Sedláková V., Mousa M., Knápek A., Sobola D.: Substrate-temperature-driven phase stabilization and strain modulation in BiFeO3/Ti/Si heterostructures for scalable silicon integration. J. Alloys Comp. 1047 (2025) 184949

Bartošák M., Mára V., Galčíková E., Slaný M., Španiel M., Poczklán L., Šulák I.: Isothermal low-cycle fatigue and fatigue-creep behaviour of boron-added 9% Cr martensitic stainless steel at 600°C. Int. J. Fatigue 193 (2025) 108800

Šiška F., Babinský T., Šulák I., Gálíková M., Kuběna I.: Numerical analysis of plastic behavior anisotropy of additively manufactured IN939 superalloy subjected to cyclic loading at high temperatures. Model. Simul. Mater. Sci. Eng. 33 (2025) 055022

Polák J., Šulák I.: Effective and internal stresses in cyclically strained materials. Results in Engineering 25 (2025) 103895

Bartošák M., Jambor M., Halamka J., Pelikán L., Stránský O., Galčíková E., Slaný M., Horváth J., Petrášek Š., Šulák I.: Low-cycle fatigue of laser powder bed fusion-processed AlSi10Mg using recycled powder: Experiments and machine learning-assisted lifetime prediction. Mater. & Design 253 (2025) 113926

Ronoh K., Novotný J., Mrňa L., Knápek A., Sobola D.: Ablation characteristics of the nickel-based superalloy, 699 XA using ultrafast laser. Appl. Surf. Sci. 682 (2025) 161687

Poloprudský J., Chlupová A., Gamanov Š., Klichová D., Stolárik G., Nag A., Hloch S.: A kernel average misorientation evaluation of surface alterations caused by angled droplet impingements. Engineering Science and Technology 69 (2025) 102126

Klichová D., Stolárik G., Nag A., Poloprudský J., Chlupová A., Fintová S., Hloch S.: Surface modification of titanium alloy Ti6Al7Nb by high-frequency droplet impingement. Wear 570 (2025) 205896

Poloprudský J., Stolárik G., Chlupová A.: Attenuation of droplet impacts on Ti alloy caused by submerged conditions. MM Science Journal 2025 (2025) 8419-8426

Mára V., Šulák I., Pelikán L., Galčíková E., Slaný M., Chlup Z., Gálíková M., Beránek L., Bartošák M.: A comprehensive study of the influence of post-processing on the microstructure evolution and high-temperature performance of Haynes 230 superalloy manufactured by laser-powder bed fusion. Journal of Materials Research and Technology 39 (2025) 4758-4779

Bartošák M., Mára V., Šulák I.: Effects of temperature and strain rate on isothermal low-cycle fatigue behaviour of Inconel 718 superalloy: Damage mechanisms, microstructure evolution, and life prediction. Int. J. Fatigue 198 (2025) 109005


Pokorný P., Vojtek T., Kubíček R., Jambor M., Náhlík L., Hutař P.: Paradox of shorter residual fatigue life due to omission of low-amplitude cycles and its significance for testing. Fatigue Fract. Eng. Mater. Struct. 48 (2025) 956-966


Šulák I., Obrtlík K.: Assessment of dwell-fatigue properties of nickel-based superalloy coated with a multi-layered thermal and environmental barrier coating. Int. J. Fatigue 191 (2025) 108693

Pelegatti M., Brůža J., Jambor M., Šiška F., Man J.: On microstructure evolution and damage onset in 316 L steel produced by laser-powder bed fusion during the early stages of low cycle fatigue loading. Mater. Character. 228 (2025) 115448


Babinský T., Šulák I., Gálíková M., Kuběna I., Poloprudský J., Náhlík L.: Room-temperature low-cycle fatigue behaviour of cast and additively manufactured IN939 superalloy. Mater. Sci. Eng. A 924 (2025) 147730

---

Sobola D., AlSoud A., Knápek A., Hamasha S., Mousa M., Schubert R., Kočková P., Škarvada P.: Field ion microscopy of tungsten nano-tips coated with thin layer of epoxy resin. Technologies 12 (2024) 193

Coskun M., Polat O., Orak I., Coskun F., Yildirim Y., Sobola D., Sen C., Durmus Z., Caglar Y., Caglar M., Turut .: The electrical and dielectric features of Al/YbFeO3/p Si/Al and Al/YbFe0.90Co0.10O3/p Si/Al structures with interfacial perovskite oxide layer depending on bias voltage and frequency. J. Mater. Sci.: Mater. Electron. 35 (2024) 1137

Daradkeh S., Recalde O., Mousa M., Sobola D., Boll T.: Oxidation behavior and outward diffusion of Al along oxide grain boundaries of FeCrAl alloys overdoped with Zr and Hf. High Temperature Corrosion of Materials 101 (2024) 41-59

Šulák I., Chlupová A., Poloprudský J., Svoboda J.: Cyclic plastic response of rotary swaged Fe-14Cr-10Al-4Y2O3 ODS alloy at 1000 -1200 °C. Mater. Character. 207 (2024) 113519

Abuamr A., Mousa M., Al-Bashaish S., Madanat M., AlSoud A., Jaber A., Alqaisi A., Al-Anber M., Barzinjy A., Arrasheed ., Sobola D.: Characterization of field emission from oxidized copper emitters. Phys. Scripta 99 (2024) 105029

Polák J., Jadlovský D., Kruml T.: Extrusions and intrusions in the cyclic plastic zone of the growing fatigue crack in polycrystalline copper. Int. J. Fatigue 179 (2024) 108063

Sirrenberg M., Bürger D., Guth S., Babinský T., Thome P., Parsa A., Eggeler G.: Out-of-phase thermomechanical fatigue of a single crystal Ni-base superalloy. Mater. Sci. Eng. A 910 (2024) 146851

Stolárik G., Klichová D., Poloprudský J., Chlupová A., Nag A., Hloch S.: Submerged surface texturing of AISI 304L using the pulsating water jet method. Archives of Civil and Mechanical Engineering 24 (2024) 207

Bartošák M., Šulák I., Horváth J., Jambor M., Pilsová L.: Isothermal low-cycle fatigue and fatigue creep behaviour of 2618 aluminium alloy. Int. J. Fatigue 179 (2024) 108027

Roth J., Šulák I., Gálíková M., Duval A., Boissonnet G., Pedraza F., Krupp U., Jahns K.: The dispersion-strengthening effect of TiN nanoparticles evoked by ex situ nitridation of gas-atomized, NiCu-based alloy 400 in fluidized bed reactor for laser powder bed fusion. J. Manufact. Mater. Process. 8 (2024) 223


Polák J., Babinský T., Vražina T., Kruml T.: Mechanism of intergranular fatigue crack growth in copper polycrystal. Int. J. Fatigue 182 (2024) 108190

Fintová S., Kuběna I., Chlupová A., Šulák I., Chlup Z., Trško L., Polák J.: Very high frequency induced fatigue damage. Theor. Appl. Fract. Mech. 133 (2024) 104590

Tkachenko S., Slámečka K., Bednaříková V., Remešová M., Gejdoš P., Ksenzova O., Valášek D., Dvořák K., Šulák I., Gálíková M., Baláž M., Deák A., Cihlář J., Čelko L.: A comparative study of the impact of La2O3 and La2Zr2O7 dispersions on molybdenum microstructure, mechanical properties, and fracture. J. Mater. Eng. and Performance 33 (2024) 14483-14494

Říha Z., Zeleňák M., Nag A., Poloprudský J., Kruml T., Hloch S.: A study of the erosion characteristics of an EN AE-6060 aluminium alloy processed using middle and high power continuous and modulated water jets. Wear 536-537 (2024) 205154

Poloprudský J., Klichová D., Stolárik G., Chlupová A.: Effect of technological parameters of the pulsating water jet on erosion effectivity on a linear trajectory. MM Science Journal 2024 (2024) 7526-7533

Hloch S., Svobodová J., Srivastava A., Srivastava M., Poloprudský J., Nag A.: Submerged pulsating water jet erosion of ductile material. Wear 538-539 (2024) 205243

Babinský T., Šulák I., Poczklán L., Guth S.: A comparison of conventional and additively manufactured 316L under thermomechanical fatigue. Int. J. Fatigue 187 (2024) 108477

Sojková T., Gröger R., Poloprudský J., Kuběna I., Schneeweiss O., Sojka M., Šiška (Kavčiaková) Z., Pongrácz J., Pizúrová N.: Kinetics of spontaneous phase transitions from wüstite to magnetite in superparamagnetic core-shell nanocubes of iron oxides. Nanoscale 16 (2024) 5551-5560



Samy V., Brasche F., Yan F., Šulák I., Bezci B., Nowak B., Berglund I., Krupp U., Haase C.: Understanding the high-temperature deformation behavior of additively manufactured y´-forming Ni-based alloys by microstructure heterogeneities-integrated creep modelling. Additive Manufacturing 88 (2024) 104256

Slone C., Mazánová V., Kumar P., Cook D., Heczko M., Yu Q., Crossman B., George E., Mills M., Ritchie R.: Partially recrystallized microstructures expand the strength-toughness envelope of CrCoNi medium-entropy alloy. Communications Materials 5 (2024) 263


Polák J., Babinský T., Vražina T., Kruml T.: The role of extrusions and intrusions in the initiation and intergranular growth of fatigue cracks. Adv. Eng. Mater. 0 (2024) 2400313

Allaham M., Dallaev R., Burda D., Sobola D., Nebojsa A., Knápek A., Mousa M., Kolařík V.: Energy gap measurements based on enhanced absorption coefficient calculation from transmittance and reflectance raw data. Phys. Scripta 99 (2024) 025952

Samy V., Brasche F., Šulák I., Verma B., Nowak B., Chlup Z., Záležák T., Schleifenbaum J., Krupp U., Haase C.: The influence of microstructural heterogeneities on high-temperature mechanical properties of additively manufactured y´-forming Ni-based alloys. Additive Manufacturing 88 (2024) 104267

Ronoh K., Novotný J., Mrňa L., Knápek A., Sobola D.: Analysis of processing efficiency, surface, and bulk chemistry, and nanomechanical properties of the Monel alloy 400 after ultrashort pulsed laser ablation. Mat. Res. Express 11 (2024) 016514

Rosenkranz L., Lan ., Heczko M., Egan A., Mills M., Feuerbacher M., Glatzel U.: Microstructure evolution and twinning-induced plasticity (TWIP) in hcp rare-earth high- and medium-entropy alloys (HEAs and MEAs) due to tensile deformation. J. Appl. Phys. 136 (2024) 025101

Bartošák M., Horváth J., Gálíková M., Slaný M., Šulák I.: High-temperature low-cycle fatigue and fatigue-creep behaviour of Inconel 718 superalloy: Damage and deformation mechanisms. Int. J. Fatigue 186 (2024) 108369

Kubíček R., Vojtek T., Pokorný P., Náhlík L., Hutař P.: Equations for efficient cycle-by-cycle computation of fatigue crack retardation and acceleration due to amplitude changes. Theor. Appl. Fract. Mech. 133 (2024) 104547

Poloprudský J., Gamanov Š., Chlupová A., Klichová D., Nag A., Stolárik G., Hloch S.: Water droplet erosion assessment in the initial stages on AISI 316L using kernel average misorientation. Tribology International 191 (2024) 109165


Sobola D., Dallaev R.: Exploring Hydrogen Embrittlement: Mechanisms, Consequences, and Advances in Metal Science. Energies 17 (2024) 2972

Ronoh K., Novotný J., Mrňa L., Knápek A., Sobola D.: Surface structuring of the CP titanium by ultrafast laser pulses. Applied Sci. 14 (2024) 3164

Knápek A., Allaham M., Košelová Z., Burda D., Podstránský J., Mousa M., Sobola D.: Comparative analysis of surface layer functionality in STM and AFM probes: Effects of coating on emission characteristics. J. Electr. Eng. 75 (2024) 268-274

Polák J., Man J., Kruml T.: The sources of cyclic slip irreversibility. Acta Mater. 267 (2024) 119709

Pedraza F., Duval A., Šulák I., Nowak B., Kepa T., Boissonnet G., Bonnet G.: Oxidation of additive manufactured 699XA Ni-based alloy under different atmospheres. Corros. Sci. 237 (2024) 112333

Hloch S., Poloprudský J., Šiška F., Babinský T., Nag A., Chlupová A., Kruml T.: Erosion development in AISI 316L stainless steel under pulsating water jet treatment. Engineering Science and Technology 50 (2024) 101630

Lintel H., Šulák I., Jahns K., Krupp U.: Manufacturing and aging behavior of CuCr1Zr powder: Analysis and modelling of close-coupled gas atomization of CuCr1Zr and its impact on the melt beam disintegration and analysis powder oxidation kinetics. Powder Technology 448 (2024) 120356

Roth J., Šulák I., Chlup Z., Fischer-Bühner J., Krupp U., Jahns K.: The dispersion-strengthening effect of TiN evoked by in situ nitridation of NiCu-based alloy 400 during gas atomization for laser powder bed fusion. Mater. Sci. Eng. A 893 (2024) 146129

Šiška F., Fintová S., Chlup Z., Kuběna I., Jambor M., Šulák I., Chlupová A.: Numerical analysis of plastic deformation mechanisms in polycrystaline copper under cyclic loading with different frequencies. Int. J. Fatigue 188 (2024) 108524

Roth J., Šulák I., Kruml T., Polkowski W., Dudziak T., Böhlke T., Krupp U., Jahns K.: Establishing a process route for additive manufacturing of NiCu-based Alloy 400: an alignment of gas atomization, laser powder bed fusion, and design of experiments. Int. J. Adv. Manufact. Technol. 134 (2024) 3433-3452

Mazánová V., Heczko M., Miao J., Mills M., Murphy-Leonard A.: The role of coherent nano precipitates on stacking fault and deformation twin formation during tensile deformation of wire arc additive manufactured nickel-aluminum-bronze. Mater. Sci. Eng. A 918 (2024) 147426

Luptáková N., Dlouhý V., Sobola D., Fintová S., Weiser A., Beneš 3rd V., Dlouhý A.: Interfaces between cranial bone and AISI 304 steel after long-term implantation: A case study of cranial screws. ACS Biomaterials Science & Engineering 10 (2024) 4297-4310

Kubíček R., Vojtek T., Jambor M., Pokorný P., Náhlík L., Pokluda J., Hutař P.: Solution to the problem of low sensitivity of crack closure models to material properties. Theor. Appl. Fract. Mech. 130 (2024) 104243

Babinský T., Poczklán L., Gálíková M., Polák J.: Importance of gamma prime shearing in low-cycle fatigue of a wrought superalloy. Fatigue Fract. Eng. Mater. Struct. 47 (2024) 1927-1943

Jambor M., Trško L., Šulák I., Šiška F., Bagherifard S., Guagliano M., Florková Z.: Application of shot peening to improve fatigue properties via enhancement of precipitation response in high-strength Al-Cu-Li alloys. Journal of Materials Research and Technology 33 (2024) 9595-9602

Fawaeer S., Al-Qaisi W., Sedláková V., Mousa M., Knápek A., Trunec M., Sobola D.: Nanometer - Thick titanium film as a silicon migration barrier. Materials Today Commun. 40 (2024) 109326


AlSoud A., Mousa M., Assayed G., Maghrabi M., Al-Jbarart A., Ronoh K., Sedlarik M., Jaber A., Abuamr A., Telfah A., Trrad I., Sedlák P., Knápek A., Sobola D.: Effect of traps and conductive pathways on electron emission from copper broad-area composite emitters. Phys. Scripta 99 (2024) 116101

Vojtek T., Kubíček R., Pokorný P., Hutař P.: Misconception of the use of 2D plane stress solutions for free surfaces of cracked bodies and its significance for full field measurement techniques. Adv. Eng. Mater. 26 (2024) 2400367

Ronoh K., Novotný J., Mrňa L., Knápek A., Sobola D.: Effects of laser and scanning parameters on surface modification of MONEL alloy 400 by picosecond laser. Opt. & Laser Technol. 172 (2024) 110514

Sirrenberg M., Babinský T., Bürger D., Guth S., Parsa A., Thome P., Dlouhý A., Mills M., Eggeler G.: The high temperature strength of single crystal Ni-base superalloys - Re-visiting constant strain rate, creep, and thermomechanical fatigue testing. Adv. Eng. Mater. 26 (2024) 2400368

Šulák I., Obrtlík K.: Thermomechanical and isothermal fatigue properties of MAR-M247 superalloy. Theor. Appl. Fract. Mech. 131 (2024) 104443

Kuběna I., Babinský T., Náhlík L., Šulák I.: Cyclic stress strain behaviour of additively manufactured gamma prime strengthened superalloy at elevated temperatures. Theor. Appl. Fract. Mech. 133 (2024) 104623

---

Polat O., Coskun F., Yildirim Y., Sobola D., Ercelik M., Arikan M., Coskun M., Sen C., Durmus Z., Caglar Y., Caglar M., Turut .: The structural studies and optical characteristics of phase-segregated Ir-doped LuFeO3-delta films. Appl. Phys. A 129 (2023) 198

Al-Anber M., Al-Qaisi W., Al-Momani ., Sobola D., Hijazi ., Mousa M., Madanat M.: Utilization of silica gel nanoparticles for selective capturing aqueous uranyl ion. J. Radioanal. Nucl. Chem. 332 (2023) 4993-5006

Šulák I., Obrtlík K.: The effect of dwell on thermomechanical fatigue behaviour of Ni-base superalloy Inconel 713LC. Int. J. Fatigue 166 (2023) 107238

Gröger R., Holzer J., Kruml T.: Twinning and antitwinning in body-centered cubic metals. Comp. Mater. Sci. 216 (2023) 111874

Mikmeková Š., Man J., Ambrož O., Jozefovič P., Čermák J., Järvenpää A., Jaskari M., Materna J., Kruml T.: High-resolution characterization of deformation induced martensite in large areas of fatigued austenitic stainless steel using deep learning. Metals 13 (2023) 1039

Janů L., Dvořáková E., Polášková K., Buchtelová M., Ryšánek P., Chlup Z., Kruml T., Galmiz O., Nečas D., Zajíčková L.: Enhanced adhesion of electrospun polycaprolactone nanofibers to plasma-modified polypropylene fabric. Polymers 15 (2023) 1686


Ronoh K., Sobola D., Mrňa L., Novotný J., Dallaev R., Knápek A., Kolařík V., Holcman V.: Characterization of the picosecond laser-ablated HOPG using Raman spectroscopy and SEM microscopy. Materials Today Commun. 34 (2023) 105181

Polák J., Chlupová A.: Mechanisms of intergranular fatigue crack initiation in polycrystalline materials. Procedia Struct. Integr. 43 (2023) 197-202

Šromová V., Sobola D., Kaspar P.: A brief review of bone cell function and importance. Cells 12 (2023) 2576

Poczklán L., Polák J., Kruml T.: Comparison of critical plane models based on multiaxial low-cycle fatigue tests of 316L steel. Int. J. Fatigue 171 (2023) 107569

Ronoh K., Fawaeer S., Holcman V., Knápek A., Sobola D.: Comprehensive characterization of different metallic thin films on highly oriented pyrolytic graphite substrate. Vacuum 215 (2023) 112345

Šulák I., Hrbáček K., Obrtlík K.: High temperature fatigue properties of boron-doped superalloy B1914. Procedia Struct. Integr. 43 (2023) 209-214

Chlupová A., Hloch S., Nag A., Šulák I., Kruml T.: Effect of pulsating water jet processing on erosion grooves and microstructure in the subsurface layer of 25CrMo4 (EA4T) steel. Wear 524-525 (2023) 204774

Guth S., Babinský T., Antusch S., Klein A., Antusch S., Šulák I.: Creep-Fatigue Interaction of Inconel 718 Manufactured by Electron Beam Melting. Adv. Eng. Mater. - (2023) 20230029

Polák J.: Role of persistent slip bands and persistent slip markings in fatigue crack initiation in polycrystals. Crystals 13 (2023) cryst130

Milovanović A., Golubović Z., Kirin S., Babinský T., Šulák I., Milošević M., Sedmak A.: Manufacturing parameter influence on FDM polypropylene tensile properties. Journal of Mechanical Science and Technology 37 (2023) 1-7


Kloenne Z., Couzinié J., Heczko M., Gröger R., Viswanathan G., Clark W., Fraser H.: On the bcc/B2 interface structure in a refractory high entropy alloy. Scr. Mater. 223 (2023) 115071

Stolárik G., Klichová D., Poloprudský J., Nag A., Hloch S.: Assessment of surface irregularities created by controlled liquid droplet on the surface of stainless steel AISI 304L. Engineering Science and Technology 47 (2023) 101558

Klichová D., Nag A., Poloprudský J., Foldyna J., Pude F., Sitek L., Hloch S.: Utilising of water hammer effect for surface roughening of Ti6Al4V. Int. J. Adv. Manufact. Technol. 126 (2023) 5633-5647

Zelený M., Ostapovec A., Fridrich L., Šesták P., Heczko M., Kruml T.: On mechanical twinning in tetragonal lattice. Philos. Mag. 103 (2023) 119-136



Al-Anber M., Al Ja´afreh M., Al-Momani ., Hijazi ., Sobola D., Sagadevan S., Al Bayaydah S.: Loading of silver (I) ion in L-cysteine-functionalized silica gel material for aquatic purification. Gels 9 (2023) 865

Shahmardani M., Logvinov R., Babinský T., Guth S., Paul S., Biswas A., Vajragupta N., Hartmaier A.: Experimental assessment and micromechanical modeling of additively manufactured austenitic steels under cyclic loading. Adv. Eng. Mater. 25 (2023) 2300103

Man J., Blinn B., Šulák I., Kuběna I., Smaga M., Chlup Z., Kruml T., Beck T., Polák J.: Formation of deformation induced martensite in fatigued 316L steels manufactured by selective laser melting (SLM). Procedia Struct. Integr. 43 (2023) 203-208

Oplt T., Vojtek T., Kubíček R., Pokorný P., Hutař P.: Numerical modelling of fatigue crack closure and its implication on crack front curvature using deltaCTODp. Int. J. Fatigue 171 (2023) 107570

Babinský T., Šulák I., Kuběna I., Man J., Weiser A., Švábenská E., Englert L., Guth S.: Thermomechanical fatigue of additively manufactured 316L stainless steel. Mater. Sci. Eng. A 869 (2023) 144831

Polat O., Coskun F., Yildirim Y., Roupcová P., Sobola D., Sen C., Durmus Z., Caglar M., Turut .: Variation in the dielectric and magnetic characteristics of multiferroic LuFeO3 as a result of cobalt substitution at Fe sites. J. Alloys Comp. 963 (2023) 170939

---

Šulák I., Obrtlík K., Čelko L.: Influence of new thermal and environmental barrier coating on the thermomechanical fatigue behaviour of nickel-based superalloy MAR-M247. Ninth International Conference on Low Cycle Fatigue 1 (2022) 139-144

Que Z., Seifert H., Mazánová V., Spätig P.: Hydrogen embrittlement on fracture resistance of low-alloy reactor pressure vessel steel with high dynamic strain aging at 288 °C. Mater. Lett. 308 (2022) 131269

Šulák I., Babinský T., Chlupová A., Milovanović A., Náhlík L.: Effect of building direction and heat treatment on mechanical properties of Inconel 939 prepared by additive manufacturing. Journal of Mechanical Science and Technology 36 (2022) 1-6

Vrchovecká K., Weiser A., Přibyl J., Kuta J., Holzer J., Pávková Goldbergová M., Sobola D., Dlouhý A.: A release of Ti-ions from nanostructured titanium oxide surfaces. Surfaces and Interfaces 29 (2022) 101699

Mazánová V., Heczko M., Polák J.: On the mechanism of fatigue crack initiation in high-angle grain boundaries. Int. J. Fatigue 158 (2022) 106721

Pisarenko T., Papež N., Sobola D., Talu S., Částková K., Škarvada P., Macků R., Ščasnovič E., Kastyl J.: Comprehensive Characterization of PVDF Nanofibers at Macro- and Nanolevel. Polymers 14 (2022) 593

Man J., Šulák I., Chlupová A., Kuběna I., Douša L., Polák J.: Cyclic plasticity and LCF behavior of AISI 316L austenitic stainless steel manufactured by selective laser melting (SLM). Ninth International Conference on Low Cycle Fatigue 1 (2022) 241-246

Šulák I., Hrbáček K., Obrtlík K.: The Effect of Temperature and Phase Shift on the Thermomechanical Fatigue of Nickel-Based Superalloy. Metals 993 (2022) 12060993

Polat O., Coskun F., Roupcová P., Sobola D., Durmus Z., Caglar M., Šikola T., Turut .: The Os substitution into Fe sites in LuFeO3 multiferroic and its effects on the electrical and dielectric features. J. Alloys Comp. 911 (2022) 165035

Šulák I., Obrtlík K., Babinský T., Guth S.: The low cycle fatigue behaviour of MAR-M247 superalloy under different strain rates and cycle shapes at 750 °C. Int. J. Fatigue 164 (2022) 107133

Poloprudský J., Nag A., Kruml T., Hloch S.: Effects of liquid droplet volume and impact frequency on the integrity of Al alloy AW2014 exposed to subsonic speeds of pulsating water jets. Wear 488-489 (2022) 204136

Guth S., Babinský T., Lang K., Hrbáček K., Šulák I.: Influence of strain-rate and cycle form on the low cycle fatigue behaviour of nickel-base superalloy MAR-M247 at high temperature. Ninth International Conference on Low Cycle Fatigue 1 (2022) 3-8

Dabees S., Mirzaei S., Kaspar P., Holcman V., Sobola D.: Characterization and Evaluation of Engineered Coating Techniques for Different Cutting Tools-Review. Materials 15 (2022) 5633

Slávik O., Vojtek T., Poczklán L., Tinoco Navarro H., Kruml T., Hutař P., Šmíd M.: Improved description of low-cycle fatigue behaviour of 316L steel under axial, torsional and combined loading using plastic J-integral. Theor. Appl. Fract. Mech. 118 (2022) 103212

Oladijo S., Mwema F., Jen T., Ronoh K., Sobola D., Akinlabi E.: Nanoscale surface dynamics of RF-magnetron sputtered CrCoCuFeNi high entropy alloy thin films. Materials Today Commun. 33 (2022) 104523

Marrow T., Šulák I., Shiuan-Li B., Vukšić M., Williamson M., Armstrong D.: High temperature spherical nano-indentation of graphite crystals. Carbon 191 (2022) 236-242

Vražina T., Šulák I., Poloprudský J., Zábranský K., Gejdoš P., Hadraba H., Čelko L.: Influence of the deposition parameters on microstructure and properties of HVOFsprayed WC-CRC-Ni coating. METAL 2022 Conf. Proc. - (2022) 487-492

Papež N., Pisarenko T., Ščasnovič E., Sobola D., Talu S., Dallaev R., Částková K., Sedlák P.: A Brief Introduction and Current State of Polyvinylidene Fluoride as an Energy Harvester. Coatings 12 (2022) 1429

Tofel P., Částková K., Říha D., Sobola D., Papež N., Kaštyl J., Talu S., Hadaš Z.: Triboelectric Response of Electrospun Stratified PVDF and PA Structures. Nanomaterials 12 (2022) 349

Kubíček R., Vojtek T., Pokorný P., Hutař P.: Sensitivity of numerically modelled crack closure to material. Procedia Struct. Integr. 42 (2022) 911-918

Chlupová A., Šulák I., Babinský T., Polák J.: Intergranular fatigue crack initiation in polycrystalline copper. Mater. Sci. Eng. A 848 (2022) 143357

Ramazanov S., Sobola D., Talu S., Orudzev F., Arman A., Kaspar P., Dallaev R., Ramazanov G.: Multiferroic behavior of the functionalized surface of a flexible substrate by deposition of Bi2O3 and Fe2O3. Microsc. Res. Tech. 85 (2022) 1300-1310

---

Orudzhev F., Ramazanov S., Sobola D., Kaspar P., Trčka T., Částková K., Kastyl J., Zvereva I., Wang C., Selimov D., Gulakhmedov R., Abdurakhmanov M., Shuaibov A., Kadiev M.: Ultrasound and water flow driven piezophototronic effect in self-polarized flexible alpha-Fe2O3 containing PVDF nanofibers film for enhanced catalytic oxidation. Nano Energy 90 (2021) 106586

Trávníček L., Kuběna I., Mazánová V., Vojtek T., Polák J., Hutař P., Šmíd M.: Advantageous Description of Short Fatigue Crack Growth Rates in Austenitic Stainless Steels with Distinct Properties. Metals 11 (2021) 475

Mikmeková Š., Man J., Konvalina I.: Microstructural characterization of 316L stainless steel fabricated by selective laser melting by advanced electron microscopy techniques. Microscopy and Microanalysis 27(S1) (2021) 2666-2668

Sobola D., Kaspar P., Částková K., Dallaev R., Papež N., Sedlák P., Trčka T., Orudzhev F., Kaštyl J., Košelová Z., Knápek A., Holcman V.: PVDF Fibers Modification by Nitrate Salts Doping. Polymers 13 (2021) 2439

Chlupová A., Šulák I., Kunčická L., Kocich R., Svoboda J.: Microstructural aspects of new grade ODS alloy consolidated by rotary swaging. Mater. Character. 181 (2021) 111477

Poloprudský J., Chlupová A., Kruml T., Hloch S., Hlaváček P., Foldyna J.: Effect of Standoff Distance on the Erosion of Various Materials. Lecture Notes in Mechanical Engineering Advances (2021) 164-171

Poloprudský J., Chlupová A., Kruml T., Hloch S.: Identification of Local Microplasticity on Ti6Al4V After Impingement of Periodically Acting Water Clusters. Lecture Notes in Mechanical Engineering Advances (2021) 63-74

Tinoco Navarro H., Holzer J., Pikálek T., Sobota J., Fořt T., Matějka M., Kruml T., Hutař P.: Determination of the yield stress in Al thin film by applying bulge test. Journal of Physics: Conference Series 1777 (2021) 012030

Heczko M., George E., Mazánová V., Ghazisaeidi M., Slone C., Polák J., Shih M., Mills M.: Role of deformation twinning in fatigue of CrCoNi medium-entropy alloy at room temperature. Scr. Mater. 202 (2021) 113985

Pirzada T., Liu D., Ell J., Barnard H., Šulák I., Galano M., Marrow T., Ritchie R.: In situ observation of the deformation and fracture of an alumina-alumina ceramic-matrix composite at elevated temperature using x-ray computed tomography. J. Eur. Ceram. Soc. 41 (2021) 4217-4230

Bertolla L., Šulák I., Buršík J., Dlouhý I., Smilek J., Mácová P., Holas J.: Exfoliation of hexagonal boron nitride nanosheets in low-modulus concentrated alkali silicate pastes. Mater. Lett. 292 (2021) 129551

Vinogradov A., Kruml T., Heczko M., Mazánová V., Linderov M.: Kinetics of cyclically-induced mechanical twinning in gamma-TiAl unveiled by a combination of acoustic emission, neutron diffraction and electron microscopy. Acta Mater. 212 (2021) 116921

Švábenská E., Chlupová A., Foldyna J., Schneeweiss O.: Evolution of Microstructure of Silicon Steel After Pulsating Water Jet Treatment. Lecture Notes in Mechanical Engineering Advances (2021) 219-228

Shabanov N., Rabadanov K., Gafurov M., Isaev A., Sobola D., Suleimanov S., Amirov A., Asvarov A.: Lignin-Based Gel Polymer Electrolyte for Cationic Conductivity. Polymers 13 (2021) 2306

Sedlak P., Sobola D., Gajdos A., Dallaev R., Nebojsa A., Kubersky P.: Surface Analyses of PVDF/NMP/[EMIM][TFSI] Solid Polymer Electrolyte. Polymers 13 (2021) 2678

Poloprudský J., Chlupová A., Šulák I., Kruml T., Hloch S.: Surface and Subsurface Analysis of Stainless Steel and Titanium Alloys Exposed to Ultrasonic Pulsating Water Jet. Materials 14 (2021) 5212

Čuha D., Nag A., Chlupová A., Hloch S.: Erosion of Titanium and Aluminium Alloys Using Pulsating Water Jet: Effect of Standoff Distance. Lecture Notes in Mechanical Engineering (2021) 56-66

Holzer J., Chlup Z., Kruml T., Gröger R.: Plastic deformation of magnetically isotropic Cr single crystals compressed at 77 K. Int. J. Plast. 138 (2021) 102938

Říha Z., Zeleňák M., Kruml T., Poloprudský J.: Comparison of the disintegration abilities of modulated and continuous water jets. Wear 478-479 (2021) 203891

Heczko M., Mazánová V., Gröger R., Záležák T., Hooshmand M., George E., Mills M., Dlouhý A.: Elemental segregation to lattice defects in the CrMnFeCoNi high-entropy alloy during high temperature exposures. Acta Mater. 208 (2021) 116719

Tinoco Navarro H., Hutař P., Kruml T., Holzer J.: Modeling of elastoplastic behavior of freestanding square thin films under bulge testing. Acta Mech. 232 (2021) 2715-2731

Polat O., Coskun F., Roupcová P., Sobola D., Durmus Z., Caglar M., Šikola T., Turut .: Influence of iridium (Ir) doping on the structural, electrical, and dielectric properties of LuFeO3 perovskite compound. J. Alloys Comp. 877 (2021) 160282

Fintová S., Kuběna I., Chlupová A., Jambor M., Šulák I., Chlup Z., Polák J.: Frequency-dependent fatigue damage in polycrystalline copper analyzed by FIB tomography. Acta Mater. 211 (2021) 116859

Babinský T., Kuběna I., Šulák I., Kruml T., Tobiáš J., Polák J.: Surface relief evolution and fatigue crack initiation in René 41 superalloy cycled at room temperature. Mater. Sci. Eng. A 819 (2021) 141520

---

Tinoco Navarro H., Hutař P., Merle B., Göken M., Kruml T.: Fracture Toughness Evaluation of a Cracked Au Thin Film by Applying a Finite Element Analysis and Bulge Test. Key Eng. Mater. 827 (2020) 196-202

Šulák I., Obrtlík K., Hutařová S., Juliš M., Podrábský T., Čelko L.: Low cycle fatigue and dwell-fatigue of diffusion coated superalloy Inconel 713LC at 800°C. Mater. Character. 169 (2020) 110599

Polák J., Petráš R.: Cyclic plastic response and damage mechanisms in superaustenitic steel Sanicro 25 in high temperature cycling - Effect of tensile dwells and thermomechanical cycling. Theor. Appl. Fract. Mech. 108 (2020) 102641

Chlupová A., Heczko M., Obrtlík K., Dlouhý A., Kruml T.: Effect of heat-treatment on the microstructure and fatigue properties of lamellar gama-TiAl alloyed with Nb, Mo and/or C. Mater. Sci. Eng. A 786 (2020) 139427

Švábenská E., Pizúrová N., Roupcová P., Chlupová A., Brajer J., Foldyna J., Schneeweiss O.: Effect of shock wave on microstructure of silicon steel. Surfaces and Interfaces 20 (2020) 100415-100425

Que Z., Heczko M., Kuběna I., Seifert H., Spätig P.: Microstructural characterization of the synergic effects of dynamic strain ageing and hydrogen on fracture behaviour of low-alloy RPV steels in hightemperature water environments. Mater. Character. 165 (2020) 110405

Petráš R., Šulák I., Polák J.: The effect of dwell on thermomechanical fatigue in superaustenitic steel Sanicro 25. Fatigue Fract. Eng. Mater. Struct. 2020 (2020) 1-16

Chlupová A., Poczklán L., Man J., Mazánová V., Heczko M., Kruml T.: Character of Fatigue Damage under Axial, Torsional and Biaxial Loading of 316L Stainless Steel. Defect Diffus. Forum 405 (2020) 264-270

Šulák I., Obrtlík K.: AFM, SEM AND TEM study of damage mechanisms in cyclically strained mar-M247 at room temperature and high temperatures. Theor. Appl. Fract. Mech. 108 (2020) 102606

Chlupová A., Šulák I., Svoboda J.: High Temperature Cyclic Plastic Response of New-Generation ODS Alloy. Metals 10 (2020) 804

Hloch S., Srivastava M., Nag A., Müller M., Hromasová M., Svobodová J., Kruml T., Chlupová A.: Effect of pressure of pulsating water jet moving along stair trajectory on erosion depth, surface morphology and microhardness. Wear 452-453 (2020) 203278

Mazánová V., Heczko M., Slone C., Kuběna I., Tobiáš J., George E., Kruml T., Polák J., Mills M.: SEM & STEM Multi-scale Characterization of Fatigue Damage in CrCoNi Medium-entropy Alloy with Fully Recrystallized Microstructure. Microscopy and Microanalysis 26 (Supp (2020) 2224

Polák J.: Production, annihilation and migration of point defects in cyclic straining. Materialia 14 (2020) 100938

---

Heczko M., Esser B., Gröger R., Feng L., Mazánová V., Wang Y., Mills M.: Structure, Morphology and Coarsening Behavior of MX (NbC) Nanoprecipitates in Fe-Ni-Cr Based Alloys. Microscopy and Microanalysis 25 (2019) 2612-2613

Šulák I., Obrtlík K., Hrbáček K.: Effect of casting conditions and heat treatment on high temperature low cycle fatigue performance of nickel superalloy Inconel 713LC. METAL 2019 Conf. Proc. (2019) 1351-1356

Kuběna M., Eliáš M., Zajíčková L., Poduška J., Kruml T.: On the Tensile Tests of Polyurethane and Its Composites with Carbon Nanotubes. Adv. Mater. Sci. Eng. 2019 (2019) 6598452

Poczklán L., Mazánová V., Gamanov Š., Kruml T.: Fatigue crack growth rate in axial, torsional and multiaxial mode in 316L austenitic steel. Procedia Struct. Integr. 23 (2019) 269-274

Mazánová V., Heczko M., Škorík V., Chlupová A., Polák J., Kruml T.: Microstructure and martensitic transformation in 316L austenitic steel during multiaxial low cycle fatigue at room temperature. Mater. Sci. Eng. A 767 (2019) 138407

Babinský T., Polák J.: Effective and internal stresses in 713LC and Rene 41 superalloys using analysis of the hysteresis loop shape. Procedia Struct. Integr. 23 (2019) 523-528

Polák J., Petráš R.: Cyclic plastic response and damage in superaustenitic steel in high temperature cycling with dwells and in thermomechanical cycling. Procedia Struct. Integr. 23 (2019) 275-280

Polák J.: Initiation and Early Growth of Fatigue Cracks. TMS 2019 Supplemental Proceedings (2019) 1125-1135

Tinoco Navarro H., Holzer J., Pikálek T., Buchta Z., Lazar J., Chlupová A., Kruml T., Hutař P.: Determination of elastic parameters of Si3N4 thin films by means of a numerical approach and bulge tests. Thin Solid Films 672 (2019) 66-74

Šulák I., Man J., Obrtlík K.: Mechanisms of fatigue crack initiation and early propagation in cyclically strained nickel superalloy. Procedia Struct. Integr. 23 (2019) 161-166

Husák R., Hadraba H., Chlup Z., Heczko M., Kruml T., Puchý V.: ODS EUROFER Steel Strengthened by Y-(Ce, Hf, La, Sc, and Zr) Complex Oxides. Metals 9 (2019) 1148

---

Heczko M., Esser B., Smith T., Beran P., Mazánová V., McComb D., Kruml T., Polák J., Mills M.: Atomic resolution characterization of strengthening nanoparticles in a new high-temperature-capable 43Fe-25Ni-22.5Cr austenitic stainless steel. Mater. Sci. Eng. A 719 (2018) 49-60

Wärner H., Calmunger M., Chai G., Polák J., Petráš R., Heczko M., Kruml T., Johansson S., Moverare J.: Fracture and Damage Behavior in an Advanced Heat Resistant Austenitic Stainless Steel During LCF, TMF and CF. Procedia Struct. Integr. 13 (2018) 843-848

Mazánová V., Polák J.: Initiation and growth of short fatigue cracks in austenitic Sanicro 25 steel. Fatigue Fract. Eng. Mater. Struct. 41 (2018) 1529-1545

Spätig P., Heczko M., Kruml T., Seifert H.: Influence of mean stress and light water reactor environment on fatigue life and dislocation microstructures of 316L austenitic steel. J. Nucl. Mater. 509 (2018) 15-28

Gröger R., Chlup Z., Kuběna I., Kruml T.: Slip activity in molybdenum single crystals compressed at 77 K. Philos. Mag. 98 (2018) 2749-2768

Man J., Järvenpää A., Jaskari M., Kuběna I., Fintová S., Chlupová A., Karjalainen L., Polák J.: Cyclic deformation behaviour and stability of grain-refined 301LN austenitic stainless structure. MATEC Web Conf. 165 (2018) 06005

Polák J., Mazánová V., Petráš R., Heczko M.: Early damage and fatigue crack initiation at ambient and elevated temperatures in heat resistant austenitic steel. MATEC Web Conf. 165 (2018) 04008

Šulák I., Obrtlík K., Čelko L., Jech D., Gejdoš P.: High-Temperature Low Cycle Fatigue Resistance of Inconel 713LC Coated with Novel Thermal Barrier Coating. Proceedings of the 17th International Conference on New Trends in Fatigue and Fracture 1 (2018) 49-56

Šulák I., Obrtlík K., Čelko L., Chráska T., Jech D., Gejdoš P.: Low cycle fatigue performance of Ni-based superalloy coated with complex thermal barrier coating. Mater. Character. 139 (2018) 347-354

Mazánová V., Heczko M., Polák J.: Fatigue crack initiation and growth in 43Fe-25Ni-22.5Cr austenitic steel at a temperature of 700°C. Int. J. Fatigue 114 (2018) 11-21

Petráš R., Polák J.: Damage mechanism in austenitic steel during high temperature cyclic loading with dwells. Int. J. Fatigue 113 (2018) 335-344

Šulák I., Obrtlík K., Čelko L., Gejdoš P., Jech D.: High-Temperature Low-Cycle Fatigue Behaviour of MAR-M247 Coated with Newly Developed Thermal and Environmental Barrier Coating. Adv. Mater. Sci. Eng. 2018 (2018) 9014975

---

Heczko M., Polák J., Kruml T.: Microstructure and dislocation arrangements in Sanicro 25 steel fatigued at ambient and elevated temperatures. Mater. Sci. Eng. A 680 (2017) 168-181

Šulák I., Obrtlík K.: Effect of tensile dwell on high-temperature low-cycle fatigue and fracture behaviour of cast superalloy MAR-M247. Eng. Fract. Mech. 185 (2017) 92-100

Karol M., Chlupová A., Mazánová V., Kruml T.: Fatigue crack initiation and growth in 316L steel in torsional cyclic loading. Eng. Mech. 23 (2017) 434-437

Mazánová V., Škorík V., Kruml T., Polák J.: Cyclic response and early damage evolution in multiaxial cyclic loading of 316L austenitic steel. Int. J. Fatigue 100 (2017) 466-476

Heczko M., Spätig P., Seifert H., Kruml T.: Correlation between Dislocation Structures and Mechanical Fatigue Response of 316L Austenitic Steel Loaded with and without Mean Stress at High Temperature in Air and Water Environment. Solid State Phenom. 258 (2017) 534-537

Holzer J., Pikálek T., Buchta Z., Lazar J., Tinoco Navarro H., Chlupová A., Kruml T.: Development of the bulge test equipment for measuring mechanical properties of thin films. METAL 2017 Conf. Proc 26 (2017) 1053-1058

Heczko M., Esser B., Smith T., Beran P., Mazánová V., Kruml T., Polák J., Mills M.: On the origin of extraordinary cyclic strengthening of the austenitic stainless steel Sanicro 25 during fatigue at 700 C. J. Mater. Res. 32 (2017) 4342-4353

Obrtlík K., Čelko L., Chráska T., Šulák I., Gejdoš P.: Effect of alumina-silica-zirconia eutectic ceramic thermal barrier coating on the low cycle fatigue behaviour of cast polycrystalline nickel-based superalloy at 900 C. Surf. Coat. Technol. 318 (2017) 374-381

Smaga M., Skorupski R., Mayer P., Kirsch B., Aurich J., Raid I., Seewig J., Man J., Eifler D., Beck T.: Influence of surface morphology on fatigue behavior of metastable austenitic stainless steel AISI 347 at ambient temperature and 300°C. Procedia Struct. Integr. 5 (2017) 989-996

Čelko L., Jech D., Dvořák J., Šulák I., Klakurková L., Obrtlík K.: Durability of Amorphous and Crystalline BMAS Thermal Barrier Coatings Produced by Plasma Spraying. Solid State Phenom. 258 (2017) 383-386

Polák J., Mazánová V., Heczko M., Kuběna I., Man J.: Profiles of persistent slip markings and internal structure of underlying persistent slip bands. Fatigue Fract. Eng. Mater. Struct. 40 (2017) 1101-1116

Čelko L., Jech D., Komarov P., Remešová M., Dvořák K., Šulák I., Smetana B., Obrtlík K.: Failure Mechanism of Yttria Stabilized Zirconia Atmospheric Plasma Sprayed Thermal Barrier Coatings Subjected to Calcia-Magnesia-Alumino-Silicate Environmental Attack. Solid State Phenom. 270 (2017) 39-44

Mazánová V., Heczko M., Kuběna I., Polák J.: Surface Relief Formation in Relation to the Underlying Dislocation Arrangement. Solid State Phenom. 258 (2017) 526-529

Šulák I., Obrtlík K.: Fatigue Crack Initiation in Nickel-Based Superalloy MAR-M247 at High Temperature. Key Eng. Mater. 754 (2017) 27-30

Man J., Chlupová A., Kuběna I., Kruml T., Man O., Järvenpää A., Karjalainen L., Polák J.: LCF behaviour of 301LN steel: coarse-grained vs. UFG-bimodal structure. Eighth International Conference on Low Cycle Fatigue 1 (2017) 205-210

Hutař P., Poduška J., Šmíd M., Kuběna I., Chlupová A., Náhlík L., Polák J., Kruml T.: Short fatigue crack behaviour under low cycle fatigue regime. Int. J. Fatigue 103 (2017) 207-215

Mazánová V., Polák J., Škorík V., Kruml T.: Multiaxial elastoplastic cyclic loading of austenitic 316L steel. Frattura ed Integrita Strutturale 11 (2017) 162-169

Chlupová A., Heczko M., Obrtlík K., Beran P., Kruml T.: Effect of Alloying and Thermal Processing on Mechanical Properties of TiAl Alloys. Solid State Phenom. 258 (2017) 501-505

Polák J., Mazánová V., Heczko M., Petráš R., Kuběna I., Casalena L., Man J.: The role of extrusions and intrusions in fatigue crack initiation. Eng. Fract. Mech. 185 (2017) 46-60

Šulák I., Obrtlík K., Čelko L., Gejdoš P.: Degradation of YSZ/EUCOR TBC Coating System during High Temperature Low Cycle Fatigue Tests. Solid State Phenom. 258 (2017) 420-423

Man J., Smaga M., Kuběna I., Eifler D., Polák J.: Effect of metallurgical variables on the austenite stability in fatigued AISI 304 type steels. Eng. Fract. Mech. 185 (2017) 139-159

Järvenpää A., Jaskari M., Man J., Karjalainen L.: Stability of grain-refined reversed structures in a 301LN austenitic stainless steel under cyclic loading. Mater. Sci. Eng. A 703 (2017) 280-292

Šulák I., Obrtlík K., Hrbáček K.: Low cycle fatigue behaviour and fatigue crack initiation in MAR-M247 at 700 °c. METAL 2017 Conf. Proc - (2017) 1580-1586

Järvenpää A., Jaskari M., Man J., Karjalainen L.: Austenite stability in reversion-treated structures of a 301LN steel under tensile loading. Mater. Character. 127 (2017) 12-26

---

Polák J., Petráš R., Heczko M., Kruml T., Chai G.: Evolution of the cyclic plastic response of Sanicro 25 steel cycled at ambient and elevated temperatures. Int. J. Fatigue 83 (2016) 75-83

Beran P., Heczko M., Kruml T., Panzner T., Petegem S.: Complex investigation of deformation twinning in gama-TiAl byTEM and neutron diffraction. J. Mech. Phys. Solids 95 (2016) 647-662

Petráš R., Škorík V., Polák J.: Damage Evolution in Thermomechanical Loading of Stainless Steel. Procedia Struct. Integr. 2 (2016) 3407-3414

Polák J., Man J.: Experimental evidence and physical models of fatigue crack initiation. Int. J. Fatigue 91 (2016) 294-303

Chlupová A., Chlup Z., Kruml T.: Fatigue properties and microstructure of quasicrystalline AlFeCrTi alloy. Int. J. Fatigue 91 (2016) 251-256

Hutař P., Poduška J., Chlupová A., Šmíd M., Kruml T., Náhlík L.: Description of short fatigue crack propagation under low cycle fatigue regime. Procedia Struct. Integr. 2 (2016) 3009-3016

Šulák I., Obrtlík K., Čelko L.: High Temperature Low Cycle Fatigue Characteristics of Grit Blasted Polycrystalline Ni-Base Superalloy. Key Eng. Mater. 665 (2016) 73-76

Polák J., Mazánová V., Kuběna I., Heczko M., Man J.: Surface Relief and Internal Structure in Fatigued Stainless Sanicro 25 Steel. Metall. Mater. Trans. A 47A (2016) 1907-1911

Šulák I., Obrtlík K., Čelko L.: High-temperature low-cycle fatigue behaviour of HIP treated and untreated superalloy MAR-M247. Kovové materiály 54 (2016) 471-481

Weidner A., Kolmorgen R., Kuběna I., Kulawinski D., Kruml T., Biermann H.: Decomposition and Precipitation Process During Thermo-mechanical Fatigue of Duplex Stainless Steel. Metall. Mater. Trans. A 47 (2016) 2112-2124

Man J., Kuběna I., Smaga M., Man O., Järvenpää A., Weidner A., Chlup Z., Polák J.: Microstructural changes during deformation of AISI 300 grade austenitic stainless steels: Impact of chemical heterogeneity. Procedia Struct. Integr. 2 (2016) 2299-2306

Petráš R., Škorík V., Polák J.: Thermomechanical fatigue and damage mechanisms in Sanicro 25 steel. Mater. Sci. Eng. A 650 (2016) 52-62

Chlupová A., Heczko M., Obrtlík K., Polák J., Roupcová P., Beran P., Kruml T.: Mechanical properties of high niobium TiAl alloys doped with Mo and C. Mater. & Design 99 (2016) 284-292

Kuběna I., Kruml T., Polák J.: Behaviour of ODS Steels in Cyclic Loading. Trans. Indian Inst. Metals 69 (2016) 309-313

Šulák I., Obrtlík K., Čelko L.: Comparative Study of Microstructure and High Temperature Low Cycle Fatigue Behaviour of Nickel Base Superalloys Inconel 713LC and MAR-M247. Key Eng. Mater. 713 (2016) 86-89

Strunz P., Petrenec M., Polák J., Gasser U., Farkas G.: Formation and dissolution of gama´ precipitates in IN792 superalloy at elevated temperatures. Metals 6 (2016) 1-12

---

Guth S., Petráš R., Škorík V., Kruml T., Man J., Lang K., Polák J.: Influence of dwell times on the thermomechanical fatigue behavior of a directionally solidified Ni-base superalloy. Int. J. Fatigue 80 (2015) 426-433

Polák J., Petráš R.: Hysteresis loop analysis in cyclically strained materials. Adv. Struct. Mater. 57 (2015) 185-205

Kuběna I., Polák J., Plocinski T., Hébert C., Škorík V., Kruml T.: Microstructural stability of ODS steels in cyclic loading. Fatigue Fract. Eng. Mater. Struct. 38 (2015) 936-947

Man J., Valtr M., Petrenec M., Dluhoš J., Kuběna I., Obrtlík K., Polák J.: AFM and SEM-FEG study on fundamental mechanisms leading to fatigue crack initiation. Int. J. Fatigue 76 (2015) 11-18

Polák J., Man J.: Quantitative model of the surface relief formation in cyclic straining. Acta Phys. Pol. A 128 (2015) 675-680

Polák J., Petráš R., Mazánová V.: Basic mechanisms leading to fatigue failure of structural materials. Trans. Indian Inst. Metals 1 (2015) 1-6

Škorík V., Šulák I., Obrtlík K., Hrbáček K.: Thermo-mechanical and isothermal fatigue behavior of austenitic stainless steel AISI 316L. METAL 2015 Conf. Proc - (2015) 851-856

Šulák I., Obrtlík K., Čelko L., Gejdoš P.: Effect of grit blasting surface treatment on high temperature low cycle fatigue life of Inconel 713LC. Multi-scale Design of Advanced Materials, Conf. Proc. - (2015) 139-144

Polák J., Petrenec M., Chlupová A., Tobiáš J., Petráš R.: Cyclic plastic response of nickel-based superalloy at room and at elevated temperatures. Materials Testing 57 (2015) 119-125

Polák J., Man J.: Initiation of stage I fatigue cracks - experiments and models. Procedia Eng. 101 (2015) 386-394

---

Man J., Valtr M., Kuběna I., Petrenec M., Obrtlík K., Polák J.: AFM and FIB study of cyclic strain localization and surface relief evolution in fatigued f.c.c. polycrystals. Adv. Mater. Res. 891-892 (2014) 524-529

Kuběna I., Polák J., Marmy P., Kruml T.: A comparison of microstructure evolution due to fatigue loading in Eurofer 97 and ODS Eurofer steels. Procedia Eng. 74 (2014) 401-404

Hutař P., Kuběna I., Ševčík M., Šmíd M., Kruml T., Náhlík L.: Small fatigue crack propagation in Y2O3 strengthened steels. J. Nucl. Mater. 452 (2014) 370-377

Polák J., Man J.: Mechanisms of extrusion and intrusion formation in fatigued crystalline materials. Mater. Sci. Eng. A 596 (2014) 15-24

Šulák I., Obrtlík K., Škorík V., Hrbáček K.: Effect of HIP on low cycle fatigue of MAR-M247 at 900°C. METAL 2014 Conf. Proc - (2014) 1381-1386

Polák J., Man J.: Fatigue crack initiation - The role of point defects. Int. J. Fatigue 65 (2014) 18-27

Obrtlík K., Hutařová S., Čelko L., Juliš M., Podrábský T., Šulák I.: Effect of thermal barrier coating on low cycle fatigue behavior of cast Inconel 713LC at 900 °C. Adv. Mater. Res. 891-892 (2014) 848-853

Kruml T., Chlupová A., Obrtlík K.: Cyclic deformation of a modern TiAl alloy at high temperatures. Adv. Mater. Res. 891-892 (2014) 1131-1136

Petrenec M., Vraspírová E., Němec K., Heczko M.: Effect of cyclic heat treatment on cast structure of TiAl alloy. Key Eng. Mater. 586 (2014) 222-225

Chlupová A., Obrtlík K., Beran P., Heczko M., Polák J., Kruml T.: Monotonic and cyclic properties of TiAl alloys doped with Nb, Mo and C. Procedia Eng. 74 (2014) 405-408

Man J., Weidner A., Klapetek P., Polák J.: Slip activity of persistent slip bands in early stages of fatigue life of austenitic 316L steel. Key Eng. Mater. 592-593 (2014) 785-788

Polák J., Man J., Kuběna I.: The true shape of persistent slip markings in fatigued metals. Key Eng. Mater. 592-593 (2014) 781-784

Polák J., Man J.: Cyclic slip localization and crack initiation in crystalline materials. Adv. Mater. Res. 891-892 (2014) 452-457

Hutař P., Kuběna I., Šmíd M., Ševčík M., Kruml T., Náhlík L.: Description of small fatigue crack propagation in ODS steel. Adv. Mater. Res. 891-892 (2014) 911-916

Polák J., Petráš R., Heczko M., Kuběna I., Kruml T., Chai G.: Low cycle fatigue behavior of Sanicro 25 steel at room and at elevated temperature. Mater. Sci. Eng. A 615 (2014) 175-182

Petrenec M., Polák J., Tobiáš J., Šmíd M., Chlupová A., Petráš R.: Analysis of cyclic plastic response of nickel based IN738LC superalloy. Int. J. Fatigue 65 (2014) 44-50

Beran P., Petrenec M., Heczko M., Smetana B., Žaludová M., Šmíd M., Kruml T., Keller L.: In-situ neutron diffraction study of thermal phase stability in a gamma-TiAl based alloy doped with Mo and/or C. Intermetallics 54 (2014) 28-38

Šmíd M., Obrtlík K.: Surface relief evolution in IN792-5A nickel base superalloy under high temperature fatigue straining with hold times. Key Eng. Mater. 592-593 (2014) 429-432

Polák J., Petráš R., Heczko M., Kruml T., Chai G.: Analysis of Cyclic Plastic Response of Heat Resistant Sanicro 25 Steel at Ambient and Elevated Temperatures. Procedia Eng. 74 (2014) 68-73

Chlupová A., Man J., Kuběna I., Polák J., Karjalainen L.: LCF behaviour of ultrafine grained 301LN stainless steel. Proc. Eng. 74 (2014) 147-150

Kruml T., Obrtlík K.: Microstructure degradation in high temperature fatigue of TiAl alloy. Int. J. Fatigue 65 (2014) 28-32

---

Slámečka K., Pokluda J., Kianicová M., Horníková J., Obrtlík K.: Fatigue life of cast Inconel 713LC with/without protective diffusion coating under bending, torsion and their combination. Eng. Fract. Mech. 110 (2013) 459-467

Kuběna I., Kruml T.: Fatigue life and microstructure of ODS steels. Eng. Fract. Mech. 103 (2013) 39-47

Polák J., Kuběna I., Man J.: The shape of early persistent slip markings in fatigued 316L steel. Mater. Sci. Eng. A 564 (2013) 8-12

Polák J., Obrtlík K., Petrenec M., Man J., Kruml T.: Mechanisms of high temperature damage in elastoplastic cyclic loading of nickel superalloys and TiAl intermetallics. Procedia Eng. 55 (2013) 114-122

Saada G., Kruml T.: Removal of plastic instabilities by reversal of the applied stress. Philos. Mag. 93 (2013) 256-271

Kruml T., Martin J.: Dislocation densities and internal stress in Ni3Al. Philos. Mag. 93 (2013) 50-59

---

Fournier B., Steckmeyer A., Rouffie A., Malaplate J., Garnier J., Ratti M., Wident P., Ziolek L., Tournie I., Rabeau V., Gentzbittel J., Kruml T., Kuběna I.: Mechanical behaviour of ferritic ODS steels - Temperature dependancy and anisotropy. J. Nucl. Mater. 430 (2012) 142-149

Giordana M., Giroux P., Alvarez-Armas I., Sauzay M., Armas A., Kruml T.: Microstructure evolution during cyclic tests on EUROFER 97 at room temperature. TEM observation and modelling. Mater. Sci. Eng. A 550 (2012) 103-11

Polák J., Man J., Petrenec M., Tobiáš J.: Fatigue behavior of ferritic-pearlitic-bainitic steel in loading with positive mean stress. Int. J. Fatigue 39 (2012) 103-108

Polák J., Man J., Petrenec M.: Damage evolution during fatigue in structural materials. Procedia Mater. Sci. 1 (2012) 3-12

Man J., Vystavěl T., Weidner A., Kuběna I., Petrenec M., Kruml T., Polák J.: Study of cyclic strain localization and fatigue crack initiation using FIB technique. Int. J. Fatigue 39 (2012) 44-53

Obrtlík K., Pospíšilová S., Juliš M., Podrábský T., Polák J.: Fatigue behavior of coated and uncoated cast Inconel 713LC at 800 °C. Int. J. Fatigue 41 (2012) 101-106

Polák J., Petrenec M., Man J., Obrtlík K.: Initiation and short crack growth in austenitic-ferritic duplex steel-effect of positive mean stress. Fatigue Fract. Eng. Mater. Struct. 35 (2012) 257-268

Kuběna I., Fournier B., Kruml T.: Effect of microstructure on low cycle fatigue properties of ODS steels. J. Nucl. Mater. 424 (2012) 101-108

---

Kruml T., Polák J.: Fatigue cracks in Eurofer 97 steel: Part I. Nucleation and small crack growth kinetics. J. Nucl. Mater. 412 (2011) 2-6

Couteau O., Kruml T., Martin J.: About the activation volume for cross-slip in Cu at high stresses. Acta Mater. 59 (2011) 4207-4215

Polák J., Petrenec M., Kruml T., Chlupová A.: Cyclic plastic response and fatigue life in symmetric and asymmetric cyclic loading. Procedia Eng. 10 (2011) 568-577

Polák J., Petrenec M., Man J.: Cyclic plasticity, cyclic creep and fatigue life of duplex stainless steel in cyclic loading with positive mean stress. Kovové materiály 49 (2011) 347-354

Kruml T., Kuběna I., Polák J.: Fatigue behaviour and surface relief in ODS steels. Procedia Eng. 10 (2011) 1690-1695

Pospíšilová S., Obrtlík K., Juliš M., Podrábský T.: Initiation and growth of fatigue cracks in Inconel 713LC with Al coating at 800 C. Chem. Listy 105 (2011) s840-s841

Obrtlík K., Pospíšilová S., Juliš M., Podrábský T., Polák J.: Low Cycle Fatigue Behavior of Cast Superalloy Inconel 713LC with Al Coating at 800 C. Key Eng. Mater. 452-453 (2011) 265-268

Man J., Obrtlík K., Petrenec M., Beran P., Smaga M., Weidner A., Dluhoš J., Kruml T., Biermann H., Eifler D., Polák J.: Stability of austenitic 316L stainless steel against martensite formation during cyclic straining. Procedia Eng. 10 (2011) 1279-1284

Kruml T., Hutař P., Náhlík L., Seitl S., Polák J.: Fatigue cracks in Eurofer 97 steel: Part II. Comparison of small and long fatigue crack growth. J. Nucl. Mater. 412 (2011) 7-12

Saada G., Kruml T.: Deformation mechanisms of nanograined metallic polycrystals. Acta Mater. 59 (2011) 2565-2574

Šmíd M., Petrenec M., Polák J., Obrtlík K., Chlupová A.: Analysis of the Effective and Internal Cyclic Stress Components in the Inconel Superalloy Fatigued at Elevated Temperature. Adv. Mater. Res. 278 (2011) 393-398

Polák J., Petrenec M., Man J., Kruml T.: Cyclic plasticity and cyclic creep in austenitic-ferritic duplex steel. Key Eng. Mater. 465 (2011) 431-434

Hutař P., Náhlík L., Ševčík M., Seitl S., Kruml T., Polák J.: Fatigue crack propagation rate in EUROFER 97 estimated using small specimens. Key Eng. Mater. 452-453 (2011) 325-328

Juliš M., Kusmič D., Pospíšilová S., Průša S., Obrtlík K., Dluhoš J., Podrábský T.: Study of surface relief evolution in cyclically strained superalloy IN738LC using advanced experimental techniques. Chem. Listy 105 (2011) 814-815

Pospíšilová S., Juliš M., Obrtlík K., Kianicová M., Podrábský T., Dvořáček O.: The Study of Microstructure and Properties of Al Diffusion Coating on Inconel 713LC. Key Eng. Mater. 465 (2011) 282-285

Weidner A., Glage A., Martin S., Man J., Fuhrmann L., Klemm V., Martin U., Polák J., Rafaja D., Biermann H.: Microstructure of austenitic stainless steels of various phase stabilities after cyclic and tensile deformation. Int. J. Mater. Res. 102 (2011) 1374-1377

Obrtlík K., Pospíšilová S., Juliš M., Podrábský T., Polák J.: Effect of Al and Al-Si diffusion coating on the low cycle fatigue behavior of Inconel 713LC. Procedia Eng. 10 (2011) 1360-1365

---

Man J., Weidner A., Kuběna I., Vystavěl T., Skrotzki W., Polák J.: Application of FIB technique to study early fatigue damage in polycrystals. J. Phys.: Conf. Series 240 (2010) 012058

Man J., Valtr M., Weidner A., Petrenec M., Obrtlík K., Polák J.: AFM study of surface relief evolution in 316L steel fatigued at low and high temperatures. Proc. Eng. 2 (2010) 1625-1633

Obrtlík K., Juliš M., Man J., Podrábský T., Polák J.: Extrusion and intrusion evolution in cyclically strained cast superalloy Inconel 738LC using confocal laser scanning microscope and AFM. J. Phys.: Conf. Series 240 (2010) 012054

---

Man J., Obrtlík K., Polák J.: Extrusions and intrusions in fatigued metals. Part 1. State of the art and history. Philos. Mag. 89 (2009) 1295-1336

Polák J., Man J., Vystavěl T., Petrenec M.: The shape of extrusions and intrusions and initiation of stage I fatigue cracks. Mater. Sci. Eng. A 517 (2009) 204-211

Man J., Klapetek P., Man O., Weidner A., Obrtlík K., Polák J.: Extrusions and intrusions in fatigued metals. Part 2. AFM and EBSD study of the early growth of extrusions and intrusions in 316L steel fatigued at room temperature. Philos. Mag. 89 (2009) 1337-1372

Obrtlík K., Petrenec M., Man J., Polák J., Hrbáček K.: Isothermal fatigue behavior of cast superalloy Inconel 792-5A at 23 and 900 °C. J. Mater. Sci. 44 (2009) 3305-3314

---

Sauzay M., Man J.: Influence of crystalline elasticity on the stress distribution at the free surface of an austenitic stainless steel polycrystal. Comparison with experiments. Mater. Sci. Forum 567-568 (2008) 149-152

Weidner A., Man J., Tirschler W., Klapetek P., Blochwitz C., Polák J., Skrotzki W.: Half-cycle slip activity of persistent slip bands at different stages of fatigue life of polycrystalline nickel. Mater. Sci. Eng. A 492 (2008) 118-127

Petrenec M., Obrtlík K., Polák J., Man J.: Dislocation structures in nickel based superalloy Inconel 792-5A fatigued at room temperature and 700 °C. Mater. Sci. Forum 567-568 (2008) 429-432

Obrtlík K., Chlupová A., Petrenec M., Polák J.: Low cycle fatigue of cast superalloy Inconel 738LC at high temperature. Key Eng. Mater. 385-387 (2008) 581-584

Fournier B., Sauzay M., Caës C., Noblecourt M., Mottot M., Bougault A., Rabeau V., Man J., Gillia O., Lemoine P., Pineau A.: Creep-fatigue-oxidation interactions in a 9Cr-1Mo martensitic steel. Part III: lifetime prediction. Int. J. Fatigue 30 (2008) 1797-1812

Polák J., Petrenec M., Man J.: Cyclic stress in 316L austenitic stainless steel at low temperatures. Mater. Sci. Forum 567-568 (2008) 401-404

---

Polák J., Man J., Vystavěl T., Zouhar L.: Fatigue crack initiation in crystalline materials - experimental evidence and models. Key Eng. Mater. 345-346 (2007) 379-382

Petrenec M., Obrtlík K., Polák J., Man J.: Effect of temperature on the low cycle fatigue of cast Inconel 792-5A. Key Eng. Mater. 345-346 (2007) 383-386

---

Petrenec M., Polák J., Obrtlík K., Man J.: Dislocation structures in cyclically strained X10CrAl24 ferritic steel. Acta Mater. 54 (2006) 3429-3443

---

Polák J., Petrenec M., Man J.: Dislocation structures and surface relief in fatigued metals. Mater. Sci. Eng. A 400-401 (2005) 405-408

Polák J., Zezulka P.: Short crack growth and fatigue life in austenitic-ferritic duplex stainless steel. Fatigue Fract. Eng. Mater. Struct. 28 (2005) 923-935

Polák J.: Cyclic plastic response and fatigue life of duplex and superduplex stainless steel. Kovové materiály 43 (2005) 280-289

Polák J.: Plastic strain-controlled short crack growth and fatigue life. Int. J. Fatigue 27 (2005) 1192-2001

---

Man J., Petrenec M., Obrtlík K., Polák J.: AFM and TEM study of cyclic slip localization in fatigued ferritic X10CrAl24 stainless steel. Acta Mater. 52 (2004) 5551-5561

---

Chlup Z., Todd I., GARCIA-ESCORIAL A., Lieblich M., Chlupová A., O´Dwyer J.: Bulk nanostructured aluminium alloy Al93Fe3Cr2Ti2: Processing and characterisation. Mater. Sci. Forum 426 (2003) 2417-2422

Man J., Obrtlík K., Polák J.: Study of surface relief evolution in fatigued 316L austenitic stainless steel by AFM. Mater. Sci. Eng. A 351 (2003) 123-132

Polák J., Man J., Obrtlík K.: AFM evidence of surface relief formation and models of fatigue crack nucleation. Int. J. Fatigue 25 (2003) 1027-1036

Polák J., Man J., Obrtlík K., Kruml T.: The shape of extrusions and intrusions produced by cyclic straining. Z. Metallkd. 94 (2003) 1327-1330

---

Man J., Obrtlík K., Blochwitz C., Polák J.: Atomic force microscopy of surface relief in individual grains of fatigued 316L austenitic stainless steel. Acta Mater. 50 (2002) 3767-3780